• <tbody id="5rwyq"></tbody>
      <rp id="5rwyq"><ruby id="5rwyq"><u id="5rwyq"></u></ruby></rp>

      <tbody id="5rwyq"></tbody>

    1. <progress id="5rwyq"><pre id="5rwyq"></pre></progress>

    2. <s id="5rwyq"></s>
      <legend id="5rwyq"></legend>

    3. 歡迎光臨濟南宏泰食品機械有限公司官方網站!

      全國咨詢熱線
      當前位置:首頁 > 公司動態 > 宏泰集團動態 >
      切片機操作規程是什么?
      發布時間:2022-04-28 23:06:54 來源:http://www.bopinkjets.com 發布人:admin

      切片機是切制薄而均勻組織片的機械,在使用切片機前,應檢查電源開關是否完整無損,擦拭機器,將載物臺移至最右邊,漏出加油口,向其中加幾滴潤滑油,多次橫向載物臺,使潤滑油均勻分布。切片機使用時遇到緊急情況應立即關閉緊急剎車開關。接下來就和小編一起來了解一下切片機使用知識吧。
      The slicer is a machine for cutting thin and uniform tissue slices. Before using the slicer, check whether the power switch is intact, wipe the machine, move the stage to the far right, leak the oil filler, add a few drops of lubricating oil to it, and cross the stage several times to make the lubricating oil evenly distributed. In case of emergency when using the slicer, turn off the emergency brake switch immediately. Next, let's learn about the use of slicer with Xiaobian.
      圖片
      picture
      一、切片機操作規程
      1、 Operating procedures of slicer
      (一)開機前準備
      (1) Preparation before startup
      1、在切片機使用之前,打開副滾筒蒸汽閥門,預熱下料盆,避免因物料和筒體之間有凝固層,而不能正常操作,一般保溫到物料成液體狀態即可。打開冷凍機,水泵及相關閥門使冷卻水置換至主滾筒中。
      1. Before the slicer is used, open the steam valve of the auxiliary drum and preheat the blanking basin to avoid the failure of normal operation due to the solidification layer between the material and the cylinder. Generally, it can be kept warm until the material becomes liquid. Open the refrigerator, water pump and relevant valves to replace the cooling water into the main drum.
      2、在使用切片機前,應檢查電源開關是否完整無損,擦拭機器,將載物臺移至右邊,漏出加油口,向其中加幾滴潤滑油,多次橫向載物臺,使潤滑油均勻分布。
      2. Before using the slicer, check whether the power switch is intact, wipe the machine, move the stage to the right, leak the oil filler, add a few drops of lubricating oil to it, and cross the stage several times to make the lubricating oil evenly distributed.
      3、在使用切片機前,應檢查刀片上是否有異物,檢查刀具護板是否蓋實,檢查磨刀砂輪是否遠離刀片。
      3. Before using the slicer, check whether there are foreign matters on the blade, whether the tool guard is covered tightly, and whether the grinding wheel is far away from the blade.
      4、在使用切片機前,應調節切割厚度,先將厚度調至大,再調至需要厚度。調好后將夾具打開,放入物料,夾實,并落下重錘。
      4. Before using the slicer, the cutting thickness should be adjusted. First adjust the thickness to the maximum, and then adjust it to the required thickness. After adjustment, open the clamp, put in the material, clamp it tightly, and drop the heavy hammer.
      (二)切片機開機
      (2) Slicer on
      1、打開電源開關。
      1. Turn on the power switch.
      2、用“箱體溫度設置按鈕”將箱體溫度設置到切片機所需溫度。
      2. Use the "box temperature setting button" to set the box temperature to the temperature required by the slicer.
      3、用“樣品頭溫度設置按鈕”設置樣品頭溫度。
      3. Use the "sample head temperature setting button" to set the sample head temperature.
      (三)切片機切片
      (3) Slicer slicing
      1、安裝好刀片,用夾緊樣刀旋鈕固定刀片,待刀片與箱體溫度一致后方能切片。
      1. Install the blade, fix the blade with the clamping sample knife knob, and slice the blade after the temperature of the blade is consistent with that of the box.
      2、用“切片厚度調節旋鈕”調節切片所需的切片厚度。
      2. Use the "slice thickness adjustment knob" to adjust the slice thickness required for slicing.


      3、將樣品放到樣品托上,涂敷包埋劑,放到冷臺上冷凍。
      3. Put the sample on the sample holder, apply the embedding agent, and freeze it on the cold table.
      4、將冷卻透的樣品放到樣品頭上,夾緊樣品托的旋鈕。
      4. Place the cooled sample on the sample head and clamp the knob of the sample holder.
      5、推進刀架使刀接近樣品,用樣品快進按鈕將樣品移近刀口。
      5. Push the knife edge close to the sample holder with the button.
      6、調節防卷板的位置,使切出的樣品平整的進入防卷板與刀片的狹縫。
      6. Adjust the position of the anti roll plate to make the cut sample enter the slit between the anti roll plate and the blade smoothly.
      7、可利用控制面板上的“鍵盤鎖按鈕”將鍵盤鎖定。
      7. The keyboard can be locked by using the "keyboard lock button" on the control panel.
      8、當停機時,應將玻璃窗打開,待機器完全干燥后再開機。
      8. When the machine is shut down, open the glass window and start the machine after it is completely dry.
      以上就是為大家介紹的有關切絲切片機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務http://wwwchinafoodjxcom/
      The above is the detailed introduction of the slicer. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://wwwchinafoodjxcom/

      上一條 : 切菜機有哪些優勢和技能?

      下一條 : 抱歉暫無數據

      相關新聞

      曹經理
      李經理
      袁經理
      4009909668
      _91亚洲精品视频_久久综合九色综合欧美98,_国产第一区在线观看